Introduction:The solar cell crushing and recycling equipment crushes solar cells and sorts out metals, silicon powder and plastics.
Workflow: The solar cells enter the shredder through the conveyor belt for the first crushing. The crushed materials pass through the vibrating feeder to separate a part of the silicon powder, and the remaining materials continue to enter the hammer crusher for the second crushing, and then enter the the circular vibrating screen separates a part of the silicon powder, and the remaining material continues to enter the grinder for the third crushing, and then enters the circular vibrating screen to separate a part of the silicon powder, and the remaining copper and plastic are screened by the air separator. The interface of the whole set of equipment is closed, and the negative pressure wind feeds the material to prevent the material from overflowing. Pulse dust removal equipment collects dust with a dust removal rate of 99%.
Advantages:
1. The operation method is simple, the separation process is environmentally friendly and non-toxic, the separation efficiency is high, the cost is low, and it is easy to handle on a large scale;
2. Compact structure, reasonable layout, stable performance and low noise.
3. Long service life, low failure rate and low maintenance cost.
4. The efficiency of pulse dust removal equipment is as high as 99%, which is effectively suppressed and has no secondary pollution.
5. The waste photovoltaic panel recycling equipment adopts PLC to control the entire production line, and the feeding is uniform.
Introduction of Independent Machines:
Double Shaft Shredder:
The main function of the double-shaft shredder is to shred large pieces. The double-shaft shredder independently drives the two main shafts to rotate forward and reverse through dual motors. Due to the mutual engagement of the moving knives, the automatic feeding function can be achieved. The cutter shaft structure, in the production process of low speed and high torque, will not cause the phenomenon of shaft winding or jamming of the equipment, thus improving the production efficiency. Adopt microcomputer (PLC) automatic control, set start, stop, reverse and overload automatic reverse control functions, the structure is simple and reasonable, and the operation and maintenance are simpler.
Hammer crusher
Hammer crushers mainly rely on impact energy to complete the operation of crushing materials. When the hammer crusher is working, the motor drives the rotor to rotate at a high speed, and the material enters the crusher cavity evenly. The high-speed rotating hammer head rushes to the baffle plate and sieve bar in the frame, and the material larger than the sieve hole size is blocked on the sieve plate and continues to be hit and ground by the hammer until it is crushed to the required discharge particle size and finally discharged out of the machine through the sieve plate.The fuselage is made of extra-thick steel plate. The lining plate and hammer head are processed by heat treatment, the chemical composition is more stable, and the service life is increased by more than 30%.
Grinder:
1. Adopted the new design special bearings, to achieve the high roating speed.
2. Convenient to install and maintence, only need to open the door to clean.
3.Completely sealing when grinding, no dust pollution.
4. The mesh sizes can be adjusted, from 10mesh to 120 mesh, and easy to adjust the grinding gap.
5. New abrasive disk design, high capacity, good wear resistance, the service life is two times longer than the common abrasive disk.
Circular Vibrating Screen
The circular vibrating screen is a high-precision fine powder screening equipment with low noise and high efficiency. Quick screen change takes 3-5 minutes, fully enclosed structure. Impurities and coarse materials are automatically discharged, and continuous operation is possible. The mesh is not blocked and the powder is not flying.
Airflow Separator
The material with small specific gravity, small particle size or large wind area sucked by the wind, and the material with large specific gravity and the same material with small wind force are discharged from the other end. It adopts automatic air circulation and integrates sorting and collection. The structure is simple and compact, and it is equipped with pulse dust collector to ensure that there is no dust overflow during the sorting process.
Pulse Dust Collector
The dust-laden gas enters from the air inlet, and when passing through the ash hopper, part of the large particle dust in the gas is separated by inertial force and gravity, and falls directly into the bottom of the ash hopper. The dusty gas enters the filter bag filter area of the middle box after passing through the ash hopper. The gas passes through the filter bag, and the dust is retained on the outer surface of the filter bag. The purified gas enters the upper box through the mouth of the filter bag, and then passes through the air outlet. discharge. It has the advantages of high purification efficiency, large gas processing capacity, stable performance, long filter bag life, convenient operation and small maintenance workload.
Powerful R&D Technical Strength and Patents
With a first-class R&D team, we invest millions of R&D funds every year to continuously develop new products and apply new technologies. The company attaches great importance to the development, accumulation and upgrading of proprietary technologies and patented technologies. It has strong equipment, process research and development capabilities and product innovation capabilities, and has a number of independent intellectual property rights. So far, it possess more than 30 sets (sets) of self-built comprehensive laboratories and international advanced experimental equipment and has obtained 6 invention patents and 20 utility model patents.
